en-US
0800 TEAM EURO
(0800 832 638)
My Name:
Email:
I want to claim my $ 50!
Attach Quote:
Please note: This offer only applies if the original quote is provided, it’s important to make sure we are comparing “apples with apples”.

Special Offer

$517.5 (incl. GST)
$14999 (incl. GST)
$172.50 (incl. GST)
$172.50 (incl. GST)
$172.50 (incl. GST)

Appliance Servicing

Whether commercial or residential if your gas appliance suddenly stops working the cause could be very simple to repair. Caution needs to be taken when selecting a gas fitting company to do the repair as in many cases YOU the consumer could end up being a guinea pig on what very often tends to be a straight forward repair, costing much more in unnecessary time and materials.

APPLIANCE REPAIR AND MAINTENANCE SERVICES

Further down the page we have listed common appliance faults with relevant remedies. Please also review our recommended maintenance procedure below.

GAS APPLIANCE REPAIR (Commercial and residential)

PRICE: $ 172.50 including (GST incl) *conditions apply Book Now

Suitable for commercial and residential appliances this booking will get a specialised, experienced and licenced gasfitter to site which will investigate and if possible remediate the fault straight away. Please note that in New Zealand there are hundreds of different gas appliance brands and it is impossible for our technicians to carry specialised parts for each brand. In most cases spare parts can be sourced immediately allowing the technician to commence repair. In cases where parts are sourced from overseas a second site visit will be required. Every additional hour will be charged at $ 125 + GST.

GAS APPLIANCE SERVICING (Commercial and residential)

WATER HEATING APPLIANCES PRICE: $299 including (GST incl) *conditions apply Book Now

COOKING APPLIANCES PRICE: $189 including (GST incl) *conditions apply Book Now

SPACE HEATING APPLIANCES PRICE: $249 including (GST incl) *conditions apply Book Now

Our Appliance Service includes the following:

  • Visually inspect ALL the gas pipe work
  • Visually inspect gas appliance, flues and ventilation
  • Working pressure at meter and standing pressure
  • strip clean or check;  Burners, Injectors, Pilot assembly, Lint arresters, Flue ways, Heat exchanger, Fan, Gas taps/valves thermostats, ignition device
  • Follow commission procedure; controls, solenoids, fan pressure switch, regulator, thermistor, thermostat, by-passes
  • General components; lights, timers, flicker devices, air / room thermostats and controls
  • Combustion performance analysis; CO / CO2 ratio (data-plate VS actual)
  • Gas Rating the appliance as per manufacturing specification
  • Final ventilation, spillage and tightness test

COMBUSTION ANALYSIS PERFORMANCE TEST

PRICE: $ 172.50 including (GST incl) *conditions apply Book Now

PLEASE NOTE: Combustion_performance_analysis The table below is ONLY an indication of what the fault may be and must be investigated and repaired by an authorised and licenced gasfitter. This information is mainly designed to educate you about your appliance and enable you to make an educated decision when you are presented with various quotes.

Measuring range Accuracy ±1 digit Resolution Adjustment time t90
Temperature (flue gas) 0.0 to 400.0 °C ±1 °C (0,0 to 100,0 °C) ±1.5 % of reading ( > 100 °C) 0.1 °C < 50 sec
Temperature (Ambient temperature -20 to +100.0 °C ± 1 °C 0.1 °C < 50 sec
Draught measurement -20.00 to +20,00 hPa ± 0.03 hPa (-3.00 to +500 hPa) ± 1.5% of m.v. (remaining range) 0.1 hPa -
Press. measurement -40,00 to +40.0 hPa ± 0.5 hPa 0.1 hPa -
O2 measurement 0,0 to 21.0 vol.% ± 0.2 vol.% 0.1 vol. % 30 sec
CO measurement 0 to 4000 ppm ±3 ppm (0 to 30 ppm) ±10 % of M.V. (31 to 200 ppm) ±20 ppm (201 - 400 ppm) ±5 % of M.V. (401 to 2000 ppm) ±10 % of M.V. (2001 to 4000 ppm) 1 ppm 60 sec
Ambient CO measurement 0 to 4000 ppm ±3 ppm (0 to 30 ppm) ±10 % of M.V. (31 to 200 ppm) ±20 ppm (201 - 400 ppm) ±5 % of M.V. (401 to 2000 ppm) ±10 % of M.V. (2001 to 4000 ppm) 1 ppm 60 sec
Determination degree of effectively (Eta) 0 to 120 % - 0.1 % -
Exhaust gas loss 0 to 99,9 % - 0.1 % -
WHY SHOULD I GET MY GAS APPLIANCE SERVICED?
COMBUSTION_NALYSIS_PERFORMANCE_TEST

An appliance should be serviced, gas rated and maintained to make sure that it is burning correctly. Not enough or too much air / gas will lower the efficiency and/or make the appliance dangerous. The appliance can overheat resulting in higher maintenance and high gas bills. A new gas appliance, once set at the correct working pressure, will usually operate at the correct gas rate. However, certain checks need to be dont to confirm factory settings.

Further examples incl: An appliance is underrated if the gas injectors are too small and overrated if the injectors are too large. Every gas appliance should legally have a data plate which provides us with operating information such as gas type, working pressure, injector size, heat input / output. Book a simple service to ensure your appliance operating as it should which will not only ensure your safety but also save you money moving forward.

 

For finance and payment options

Certifications

My Name:
Email:
I want to claim my $ 50!
Attach Quote:
Please note: This offer only applies if the original quote is provided, it’s important to make sure we are comparing “apples with apples”.

A quote will be sent to you within 30 minutes*

+ =
PREVIOUS 

Important

Please provide as many details as possible to simplify the quoting process. If the information you have provided is sufficient, you will be notified within the given times below. If a site visit or any further information is required, our team will advise you accordingly.

Questions?

0800 TEAM EURO

*In peak times quotes can take up to 2 hours, larger quotes are subject to free site visits, you will be advised on progress by email.

Success! Your information was sent through.

A team member will be in touch shortly.
Questions? Please call 0800 TEAM EURO

loading...

Pay your invoice online!

Enter your Invoice Number below: (e.g. INV-123456)

PLEASE NOTE: You must include the "INV" before entering the six digit invoice number itself. The format must be as follows: INV-123456

Leave a Message